CCTV

Did you know that the glass break sensor is one of the most important features for your home security? It detects any break-in attempt through your windows or doors and alerts you immediately. Your safety is our utmost priority

Activating a new TPMS sensor without a tool can be quite challenging. However, there is a way around it. Inflate the tire to 40 PSI and release the air in less than 10 seconds. Repeat this process until you hear a beep sound. This indicates that the TPMS has been activated successfully.

SimpliSafe entry sensors have a built-in tamper switch that, when triggered, sends a signal to the base station. Tampering can occur when the sensor is detached from its mount or if the cover is removed. If your sensor detects tampering, it will beep for 30 seconds and then go silent. Resetting the sensor gets rid of any tampering alerts and silences the beeping.

Are you having trouble opening or closing your garage door? Call the experts today! We are here to help you with all your garage door repair needs. From broken springs to faulty openers, we fix it all

The camshaft position sensor is an essential component of a vehicle’s engine. It helps in determining the position of the camshaft to regulate the fuel injection and ignition timing. Here’s how you can test your car’s camshaft position sensor: 1. Locate the Sensor 2. Disconnect the Wiring Harness 3. Use a Multimeter 4. Test for Resistance 5. Check for Voltage Output 6. Replace if Needed

Alarms are designed to keep you safe, but there may be times when you need to bypass them for a short period. Here’s how you can do it: 1. Open the door. 2. Press your code + OFF. 3. The alarm will beep. 4. Close the door within 10 secs. 5. The sensor will re-engage after 45 secs. Stay safe and secure!

Flame sensors are an important safety feature in many appliances and devices. They help detect the presence of a flame and shut off the fuel supply if no flame is detected. If you’re testing a flame sensor, here’s how to do it.

A fire alarm system is essential for the safety of life and property in a building. Don't put it off for later, install a fire alarm system today

When your car battery dies, the alarm system might go off when you connect jumper cables. If this happens, try unlocking the driver’s side door with your key to turn off the alarm.

To turn off the SimpliSafe smoke alarm, press and hold the test button on the device until you hear a single beep. The device will then stop beeping, and you won’t receive any more alerts.

Smoking in your apartment can be quite challenging, especially if you have a fire alarm installed. However, it’s not impossible. Read on to find out how you can smoke in your apartment without setting off the alarm.

Karr Alarm System can be quite a nuisance once you decide to sell your car. While it’s a great system for personal use, it doesn’t always sit well with the new owner. Here are three ways you can remove Karr alarm from your vehicle. #KarrAlarm #VehicleSafety 1. Remove the Fuse 2. Disconnect the Battery 3. Find the Control Module

The Ring doorbell is a beneficial tool in today’s time. However, too many random notifications can be bothersome. If you want to know how to turn off an alert from your neighbor’s ring doorbell, follow these quick steps.

If you want to find the IP address of a CCTV camera, you can do so by following these steps: 1. Connect the CCTV camera and your computer to the same network. 2. Download an IP scanner software or use the Command Prompt on Windows. 3. Run the IP scanner software and it will display all the devices connected to the network, including your CCTV camera. 4. Note down the IP address of your CCTV camera from the list. That’s it! You now have the IP address of your CCTV camera.

Using a baby monitor is essential for all new parents. And if you’re struggling with ways to mount it, we’ve got you covered. A baby monitor can be mounted on a wall, attached to the crib, or placed on a table so that you can keep an eye on your little one at all times.